Search results for "Sheet resistance"
showing 10 items of 14 documents
Light absorption and electrical transport in Si:O alloys for photovoltaics
2010
Thin films (100-500 nm) of the Si:O alloy have been systematically characterized in the optical absorption and electrical transport behavior, by varying the Si content from 43 up to 100 at. %. Magnetron sputtering or plasma enhanced chemical vapor deposition have been used for the Si:O alloy deposition, followed by annealing up to 1250 °C. Boron implantation (30 keV, 3-30× 1014 B/cm2) on selected samples was performed to vary the electrical sheet resistance measured by the four-point collinear probe method. Transmittance and reflectance spectra have been extracted and combined to estimate the absorption spectra and the optical band gap, by means of the Tauc analysis. Raman spectroscopy was …
Modification of the sheet resistance under Ti/Al/Ni/Au Ohmic contacts on AlGaN/GaN heterostructures
2018
This paper reports on the modification of the sheet resistance under Ti/Al/Ni/Au Ohmic contacts on AlGaN/GaN heterostructures, studied by means of Transmission Line Model (TLM) structures, morphological and structural analyses, as well as computer simulations. In particular, the contacts exhibited an Ohmic behaviour after annealing at 800 degrees C, with a specific contact resistance rho(c) = (2.4 +/- 0.2) x 10(-5) Omega cm(2), which was associated to morphological and structural changes of both the metal layer and the interface. Interestingly, TLM analyses gave a value of the sheet resistance under the contact (R-SK = 26.1 +/- 5.0 Omega/rectangle) significantly lower than that measured out…
Solution-processible electrode materials for a heat-sensitive piezoelectric thin-film sensor
2012
Abstract Piezoelectric sensors are needed in a wide range of applications from physiological measurement applications to industrial monitoring systems. Custom-designed, highly integratable and cost-effective sensor elements can be manufactured by using flexible materials in combination with high-throughput printing for fabrication. This would also enable the embedding of ubiquitous sensors in our living environment to improve the common welfare. Here, we have fabricated flexible piezoelectric sensor elements using printing methods. We demonstrated that alternative, printable electrode materials are compatible with temperature-sensitive functional substrates. Low-temperature curable electrod…
Correlated effects of fluorine and hydrogen in fluorinated tin oxide (FTO) transparent electrodes deposited by sputtering at room temperature
2021
The optical and electrical properties of fluorinated tin oxide (FTO) films deposited at room temperature by sputtering have been investigated varying the fluorine content and the hydrogen atmosphere. The complex behavior of the obtained films is disclosed using a wide set of characterization techniques that reveals the combined effects of these two parameters on the generated defects. These defects control the electrical transport (carrier density, mobility and conductivity), the optical properties (band gap and defects-related absorption and photoluminescence) and finally promote the amorphization of the samples. H2 in the sputtering gas does not modify the H content in the films but induc…
Frequency dependence of the microwave surface resistance of MgB2 by coaxial cavity resonator
2014
Abstract We report on the microwave (mw) properties of a cylindrical MgB2 rod prepared by the reactive liquid Mg infiltration technology. The MgB2 rod, 94.3 mm long, is used as inner conductor of a coaxial cavity having a Cu tube as external conductor. By analyzing the resonance curves of the cavity in the different resonant modes and at different temperatures, we have determined the temperature dependence of the mw surface resistance, R s , of the MgB2 material, at fixed frequencies, and the frequency dependence of R s , at fixed temperatures. Our results show that the R s ( f ) curves follow a f n law, where n decreases on increasing the temperature, starting from n ≈ 2 , at T = 4.2 K , d…
Spatiotemporal colorimetry to reveal electrochemical kinetics of poly(o-toluidine) films along ITO surface
2018
Abstract Sheet resistance of transparent conducting electrodes can affect dramatically the electrochromic response of surface confined active species in any electrochromic device. The generated gradient of effective potential on the electrode surface has a direct impact on the electrochemical kinetics of these species. In this work, the electrochromic poly (o-toluidine) (POT) film, a derivative polyaniline, was deposited along a narrow, long transparent indium tin oxide (ITO) supporting electrode with a sheet resistivity of 30 Ω cm−1. This configuration was used as a model to simulate a surface electrical conduction from the external metallic contact to the opposite extreme of ITO with an i…
Tantalum nitride thin film resistors by low temperature reactive sputtering for plastic electronics
2008
This article describes the fabrication and characterisation of tantalum nitride (TaN) thin film for applications in plastic electronics. Thin films of comparable thickness (50-60 nm) have been deposited by RF-magnetron-reactive sputtering at low temperature (100 °C) and their structure and physical (electrical and mechanical) properties have been correlated by using sheet resistance, stress measurements, atomic force microscopy (AFM), XPS, and SIMS. Different film compositions have been obtained by varying the argon to nitrogen flow ratio in the sputtering chamber. XPS showed that 5:1, 2:1 and 1:1 Ar:N 2 ratios gives Ta 2 N, TaN and Ta 3 N 5 phases, respectively. Sheet resistance revealed a…
Zinc oxide and indium tin oxide thin films for the growth and characterization ofShewanella loihicaPV-4 electroactive biofilms
2011
Transition metal oxides (TMO) electrodes provide a suitable platform for spectroscopy- and microscopy-based investigation of viable electroactive biofilms (EABs). Commercially available TMOs, such as indium titanium oxide (ITO), are produced from rare and expensive elements. Thus, there is a significant need to explore alternative technology to meet the demand. ZnO-based TMOs are low-cost and have excellent electrochemical properties. In this study, we report for the first time a model EAB of Shewanella loihica PV-4 on ZnO films deposited on perspex substrates via pulsed laser deposition (PLD). Commercially available ITO electrodes were also used for comparison. 480 Virulence Volume 2 Issue…
Microwave response of a cylindrical cavity made of bulk MgB2 superconductor
2008
We report on the microwave properties of a resonant cylindrical cavity made of bulk MgB2 superconductor, produced by the reactive liquid Mg infiltration process. The frequency response of the cavity has been measured in the range 5-13GHz. Among the various modes, the TE011, resonating at 9.79GHz, exhibits the highest quality factor. For this mode, we have determined the temperature dependence of the quality factor, obtaining values of the order of 10^5 in the temperature range 4.2-30K. The values of the surface resistance deduced from the measurements of the quality factor agree quite well with those independently measured in a small sample of MgB2 extracted from the same specimen from whic…
Microwave Response of Coaxial Cavities Made of Bulk Magnesium Diboride
2014
We report on the microwave (mw) properties of coaxial cavities built by using bulk MgB2 superconductor prepared by reactive liquid Mg infiltration technology. We have assembled a homogeneous cavity, by using an outer MgB2 cylinder and an inner MgB2 rod, and a hybrid cavity by using an outer copper cylinder and the same MgB2 rod as inner conductor. By the analysis of the resonance curves, in the different resonant modes, we have determined the microwave surface resistance, Rs, of the MgB2 materials as a function of the temperature and the frequency, in the absence of DC magnetic fields. At T = 4.2 K and f = 2.5 GHz, by a mw pulsed technique, we have determined the quality factor of the homog…